And while the 5R110W's capabilities as a stout transmission have proven itself, the shear capability of producing high levels of horsepower out of the 6. Also, wrap tape around the joint caps to keep them from falling off and the pins from falling out of the caps. Features: For R and R of Fuel Filter, Transmission and Oil cooler linesQuick Line RemovalAnodized Aluminum ConstructionKit includes all pieces from the 8100 and 8107 line disconnect sets. Tip: When pulling the driveshaft out of the transmission, be careful not to allow it to fall hard to the floor. Rick Answered on Nov 23, 2014 If I understand what is happening, your window is dropping inside the door by itself or not traveling correctly under power.
The transmission weighs about 70 pounds. Note: The fluid will need to be drained from the converter regardless of whether you plan to reuse it or replace it. Once the crossover pipe is removed, look closely at the exhaust pipe, the section of the exhaust system that includes the catalytic converter and muffler to determine if it also needs to be removed. The braided line needs to be unlocked and removed in order to remove the oil rail. In this picture, you can get an idea of how the air conditioning compressor is mounted to the engine.
Lisle 39960 2-Pc Transmission Oil C. Interior Lights Step-1: Remove Air Cleaner Start by removing the air cleaner assembly. Remove any starter bolts that are accessible. What is a fair price to pay for various transmission repairs? The fittings will leak if these washers are not replaced. Step-2: Remove Air Conditioning Condenser Remove the front grille and the headlight assembly to gain access to the cooling accessories in the front. Do not use power tools.
Where is the starter on a 1986 nissan stanza station wagon and how do you get to it? Non-stock item, manufacturer drop ship; please email service toolsource. Brake System Front Disc Brake 206-04. Lisle 39960 2-Pc Transmission Oil C. Each lifter hold-down supports four lifters. Fuel System Speed Control 412-00. Assenmacher 8110 10-Pc Line Disconnect Set. Fuel System: Transit Connect: 2011Fuel System: Transit Connect: 2010Fuel Charging and Controls -- 2.
Body Handles, Locks, Latches And Entry Systems 501-16. Below is a diagram of a standard relay Ford uses. Step-3: Remove Transmission Cooling Lines If the vehicle is equipped with automatic transmission, remove the transmission cooling lines from the lower part of the radiator. So what does a No Hassle Warranty really mean? Double Overwound torsion spring designed for longer life. Remove the 4 U-joint bolts that hold the driveshaft to the rear differential. Used for R and R of Transmission Oil Cooler Lines Orange-Anodized Aluminum Construction Quick line removal Included in the 8110 Line Disconnect Set Applications include: Ford - Edge, Ford - Escape 2009 - 2009Fits 2009 Escape with 6F TransFits 2012 Ford EdgeFord - Excursion with 6.
Sometimes paying someone to do a job to prevent breaking the glass is a small trade-off. View the service manual on your computer or print off pages as needed. Step-9: Remove Inner Fan Shroud Bolts Earlier, the inner fan shroud bolts were removed from the top of the intake manifold. Safety Tip: To eliminate any chance of battery arching, after removing the battery cable, wrap a rag around the cable end and place a wrap over the battery terminal. There should be two on each side. You'll need to support the motor.
Driveline Wheel Hubs And Bearings — Full Floating Axle — Dana 205-02D. Step-5: Remove Up Pipe Assembly Before removing the engine, you need to remove the exhaust up pipe assembly from each exhaust manifold and remove the up pipe assembly from the engine compartment. Remove ball joint nuts 17 mm. General Information Service Information Maintenance Schedules Description And Operation Maintenance Schedual — 6. Step-8: Remove Outer Fan Shroud Remove the outer fan shroud, which exposes the engine fan and the inner fan shroud. Remove 5 engine crossmember mounts 3 bolts, 2 nuts 14mm. Was this review helpful to you? You may need to raise or lower the jack slightly or move it slightly to one side or the other to line up the dowels with the dowel holes.
Engine Engine Emission Control 303-12. The lines are the blade contacts on the bottom of the relay. Get both starter bolts started before fully tightening the bolts. And as always, if you need assistance in determining the correct parts for you, give us a call or send an e-mail to and we would be happy to help. Engine Intake Air Distribution And Filtering 303-13.
Nov 03, 2010 Yes, shouldn't be a problem. Electrical Audio Systems Information And Entertainment Systems 417-01. Plug in any top side electrical connectors and vacuum hoses. When disconnecting hoses and cables, make a drawing showing how each one is routed. When the transmission is in position, carefully slide the jack forward until the bell housing touches the back of the engine.
Has adj-bracket with rubber insulators Fig 6, Items B, C. Vehicle owners become aware of a transmission fluid leak either when checking the fluid level and seeing that it is low or seeing a red colored fluid on their driveway or garage floor. I usually scribe the valve covers with small lines. Remove the fan and the inner shroud to expose the front of the engine. When the dowel pins are in the dowel holes, install the bell housing bolts.