Learn and ob- serve all the rules below. When the engine starts, the water pump turns and the coolant circulates. Clutch Lever Free Play Inspection. Oil Pressure Switch T6: 1. L: Apply a non-permanent locking agent.
Not a bad peak horsepower output for the displacement, and pretty remarkable, really, given the 7,000 rpm spread of thrust between 8,000 and 15,000 rpm. . Measure the clearance when engine is cold. Wind protection from the fairing was surprisingly good, despite its small frontal area. Match clearance in vertical column with present shim size in horizontal column.
Footpeg Bracket Mounting Bolts 5. Accessory Fuse 10 A G. If the connector is corroded or dirty, clean it carefully. . A marking hollow facing forward. Illustrations and photographs in this publication are intended for reference use only and may not depict actual model component parts.
It was introduced in 1995, and has been constantly updated throughout the years in response to new products from , , and. Clamp Installed to the front fender 5. We can take nearly any type of vehicle on trade, and we also buy motorcycles outright and offer a consignment option to help sell the bike on your behalf. Any Questions Call 901-531-0724 I Will Add A Video Of The Bike Running Soon. This can damage or warp the disc.
Some inspections take 3-5 days or more so please call to confirm time frame. If the seals are not satisfactory, pad wear will increase, and constant pad drag on the disc will raise brake and brake fluid temperature. Reserve Tank Overflow Hose 14. The alternator is on the left-hand end of the crankshaft and the rotor carries the starter clutch. If the shaft is bent, straighten or replace it. We suspected this was not, in fact, the case, instead being a misperception brought on by the huge top-end rush the 6R provides.
Kawasaki seems to have mated this rigid fork design with chassis rigidity quite well. Torque - Carburetor Holder Bolts: 12 N·m 1. The front wheel should swing fully left and right from the force of gravity until the fork hits the stop. If the gauge is lowered and then raised again, the fuel level measured shows somewhat higher than the actual fuel level. If they are damaged, replace them.
Torque - Crankcase 8 mm Bolts: 30 N·m 3. Periodic Maintenance Chart Other than United States and Canada Models. The 6R will wheelie whether you want it to or not, so be ready! Be sure that all parts are put back in the cor- rect sequence and all circlips and washers are properly in place. Catalyst Protection System When excessive unburned gasoline flows more than the allowable amount into the exhaust gas dur- ing running, the temperature of the catalysts rises abnormally because the unburned gasoline reacts with heated catalysts at the activation temperature or higher. Closed coil end faces downward.
At the same time, steering feels light due, at least in part, to the small, 280mm brake discs, which reduce gyroscopic effect on the front end. It is the amount and spread of power that just about knocks you out, however, not its smooth delivery. Breather Hose To Canis- 2. The push rod does not return to its original position once it moves out to take up camshaft chain slack. Most 600s require a tug on the bars, and a weight shift to boot.
If the damping feels too soft or too stiff, adjust it in accordance with the following table. And check out the rating of the bike's You can compare the rating with other bikes. This shim will give the proper clearance. Right Handlebar Switch Lead 6. Radiator Fan Motor Lead 9.
High Beam Indicator Light 11. Related bikes List for comparison of specs. Engine Oil and Oil Filter. Make sure the area is well-ventilated and free from any source of flame or sparks;. Sealant - Kawasaki Bond Silicone Sealant : 56019-120 Torque - Oil Pressure Switch: 15 N·m 1. Torque - Front Axle Clamp Bolts: 20 N·m 2. Headlight Fuse 10 A 17.