It is for vehicles that are not operated under any of the conditions listed under Schedule ЉBЉ. The correct position places the long narrow void out- board of the bushing and the short wide void inboard of the bushing Fig. Make sure the toe setting does not change dur- ing clamp tightening. Only lubricants bearing designations defined by the following organization should be used. The formula to use the check digit is not released to the general public.
Remedy Chrysler notified owners and launched its recall campaign in January 2014. If you buy good-quality fuel and fol- low the cold-weather advice above, fuel conditioners should not be required in your vehicle. Install the nut on top of the tool at the shock hole. Remedy Chrysler will notify owners, and dealers will replace the passenger frontal air bag, free of charge. Owners may contact Chrysler at 1-800-247-9753.
X X X Drain and refill transfer case fluid. Electrical systems can be damaged on either vehicle. This will ensure the steering wheel will be centered when the wheels are positioned straight-ahead. To avoid component damage, a wheel-lift towing vehi- cle or a flat-bed hauling vehicle is recommended. These claims have not been sup- ported to the satisfaction of DaimlerChrysler and these additives must not be used. Steering linkage attached to the knuckle allows the vehicle to be steered. In addition, 100 percent ethylene-glycol freezes at -22°C -8°F.
This will increase the longevity of the tool and insure proper operation during the removal and installation pro- cess. This angle enables the front wheels to return to a straight ahead position after turns Fig. We will 100% be ordering more parts from Geno's! Install the pivot bolts and nuts. The bell-shaped adapter goes against the lower suspension arm. Observe the steering wheel return-to-center position. A vehicle with flat-bed device can also be used to transport a disabled vehicle Fig. If necessary, remove the wheels from the lifted end of the vehicle and lower the vehicle closer to the ground, to increase the ground clearance at the opposite end of the vehicle.
Refer to Suspension and Steering System Diagnosis Chart below for additional information. Identification is determined by the line marks on the top of each bolt head. If the viscosity stays con- stant through the temperature range of operation, transmission operation and shift feel will remain con- sistent. X Change front axle fluid 4X4. Support the vehicle in the raised position with jack stands at the front and rear ends of the frame rails Fig.
If springs are not at their normal ride position, vehicle ride comfort could be affected and premature bushing wear may occur. X Inspect engine air cleaner filter, replace if necessary. Select an engine oil that is best suited to your par- ticular temperature range and variation Fig. Tighten the upper ball joint nut to 54 N·m 40 ft. Also when front suspension components have been replaced. Make sure the toe setting does not change dur- ing clamp tightening.
The coolant must accept heat from engine metal, in the cylinder head area near the exhaust valves and engine block. When service is required, DaimlerChrysler Corpo- ration recommends that only Mopar brand parts, lubricants and chemicals be used. The fluid must also be thermally stable so that it can maintain a consistent viscosity through a large temperature range. The identifying notations are located on the front label of engine oil plastic bottles and the top of engine oil cans Fig. Separate the ball joint from the knuckle with Remover 8677 Fig. This will change the camber angle significantly and little effect on the caster angle using special tool 8876 to move the upper control arm for proper adjustment. Consequently, odor and color cannot be used to indicate the fluid condition or the need for a fluid change.
Be sure there is adequate ground clearance at the oppo- site end of the vehicle, especially when towing over rough terrain or steep rises in the road. Maximum protec- tion against freezing is provided with a 68 percent antifreeze concentration, which prevents freezing down to -67. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these capacities may vary. Damage to the cab, cargo box or frame may result. Loose or worn steering or suspension components.
X X X X X Check transfer case fluid level. When a second vehicle code plate is necessary, the first four spaces on each row will not be used because of the plate overlap. This kit includes 2003-05 style rocker box, 3 2003-05 style injector wiring harnesses, 3 injector harness bolts, valve cover gasket, rocker box gasket, Hoesli Diesel conversion harness to take your 2 6 pin connectors to the 3 4 pin connectors. The recall began on March 16, 2016. If engine does not start within 15 sec- onds, stop cranking engine and allow starter to cool 15 min. The actual bolt strength grade corresponds to the number of line marks plus 2.
To increase positive caster angle, move the rear position of the upper control arm inward toward the engine. It is important to have the springs supporting the weight of the vehicle when the fasteners are torqued. Tighten or replace components as necessary. We've loaded the bed full of concrete bags, dropped 6000-plus pounds of weight on the hitch, and our…. This coolant offers the best engine cooling without corrosion when mixed with 50% Ethylene Glycol and 50% distilled water to obtain a freeze point of -37°C -35°F.